Page Threads

If anyone is interested, you can flash the wm6.1 rom to your SDA. I have successfully done this on 2 Tmobile SDA handsets. It is a fairly simple process (I've never done anything of the sort, and it was easily done for me) with this walkthrough that I found.

Here's the address for the site: http://karhoe.net/content/view/21/1/

You've just got to make sure you use the correct rom for the sda, which is included for download in the walkthrough. Also, you can find other Roms on xda-developers if you care for something else, but I'm loving the new 6.1 interface.

So if you want wm6 on the sda, it can be done. A word of caution, make sure to follow all the steps carefully because as the walkthrough points out, if you don't you could make an expensive paperweight :)
-Best Wishes

 out of  found this valuable. Do you find this valuable?    

Do you know if this will work with a sprint mogul?

1  out of 1 found this valuable. Do you find this valuable? Do you?    

its a 2.5mm jack

 out of  found this valuable. Do you find this valuable?    

Pay as you go is lots more espensive than small data plans. Keep that in mind. being that the case, then again, my suggestion would be, go into CONNECTION SETTINGS... GPRS... You will see one or more connections in there. In my case with Suncom Wireless I got 3 (iNet, iLink, MMS) If you go in the settings of each and add anything to the "access point' line, that will give a Connection error if trying to connect via GPRS. Whenever you do want to you it, go manually and undo the changes you did and your good to go.

3  out of 5 found this valuable. Do you find this valuable? Do you?    

I've put mine apart several times; it’s tricky, but not impossible. I'll try to explain. First let’s keep in mind this phone is basically 4 parts (1 battery cover, 1 top cover, 1 face plate, 1 back plate and the motherboard).

1. Start by removing the battery cover, battery, sim and memory card.
2. Remove top cover (where cam is) by sliding a small thin flat screwdriver by the sides, from bottom towards top (as if you were ridding the screw driver thru the sides where the battery cover slides in) and gently twist it. You need to do this on both lower ends of that top cover and it will pop off.
3. There are 6 screws total. 2 under that top cover and 4 in the battery compartment (1 is hiding under security seal). Remove all 6, notice they are different size. Remember the 2 small ones go in the center when assembling back.
4. Using a credit card or similar plastic object, slide it between back plate and face plate. Start near the Cam soft key, move down towards the mini USB. There are approximately 6 points (3 on each side) where bottom attaches to the top, so play with it till you get the sides slightly open.
5. Once sides are popped open, look inside; you need to unplug the cam. Gently pry it up off the socket.
6. Slide back plate down (keep your eyes on the mini USB, it tends to stick there) and put it aside. There is another plug that comes from the keyboard (face plate) that needs to be carefully unplugged from the motherboard.
7. LCD is connected to the mother board, so when removing the motherboard, be careful not to mess up the LCD connection and wiggle it gently till the LCD separates from the face plate lens.
8. Avoid touching the LCD or inside of the faceplate lens, as its a pain in the butt to clean them and leave them w/o marks.
9. Assemble back in reverse order. Beware when placing back the LCD on the face cover. Make sure it sits perfectly in place. Don't force anything, it all falls in place.

10  out of 10 found this valuable. Do you find this valuable? Do you?    

I took mine apart and cleaned it, but it simply had a defective joystick--not dirt. Check for broken screens/bad flashes on ebay and scavenge from those.

 out of  found this valuable. Do you find this valuable?    

not working here. might have had issues with the hard typing the regedit part. could not edit this ref series:
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\BtA2dpSnd]
any help or anyone have a copy of their registry?

2  out of 2 found this valuable. Do you find this valuable? Do you?    

google for a cab file that removes the startup sound. idk what it is called now but i uesd it and it workd great.

 out of  found this valuable. Do you find this valuable?